Get a quote
EN ⌄
English简体中文Русский

HSY · BUYING GUIDE

How to Choose Power and Capacity for Energy Storage

Choose output power to match the equipment you need to run, then estimate energy capacity for the required operating time. A useful purchasing brief covers continuous load, startup demand, runtime and the actual electrical configuration—not just the largest number on a specification sheet.

1. What do W, kW, Wh and kWh mean?

W and kW describe power at a particular moment; 1 kW equals 1,000 W. Wh and kWh describe energy; 1 kWh equals 1,000 Wh. For a constant load, energy use is power multiplied by operating time. See the EIA explanation of electricity measurement.

A hypothetical 100 W load running for three hours needs 300 Wh at the load. The battery may need to store more because the usable energy window, conversion losses and system consumption affect how much energy reaches the equipment.

Do not compare Ah alone across different voltages. At the nominal voltage of the same battery pack, Wh is approximately V × Ah. Do not mix cell voltage, assembled-pack capacity and AC output voltage.

2. Rated output versus peak output

Rated output describes continuous load capability under the specified conditions. Peak or surge output applies only for a limited duration and under defined conditions. It is not a substitute for the continuous rating. Motors and compressors can have startup requirements different from their running demand; obtain the equipment’s startup data and compare it with the inverter’s overload-duration curve rather than applying one universal multiplier.

Add the continuous power of equipment that can run together, then check the worst relevant startup combination. Also check voltage, frequency, phase arrangement, port or per-phase limits and current limits. Where equipment is rated in VA, distinguish apparent power from real power in W; the figures are not automatically interchangeable.

Allow for planned additions, temperature-related derating and variable loads as appropriate. There is no single margin that guarantees compatibility for every application. Meeting a power figure is only one part of the equipment check.

3. Estimate runtime with explicit assumptions

For an initial constant-AC-load estimate:

Runtime (hours) ≈ nominal energy (Wh) × usable fraction ÷ [load power (W) ÷ inverter efficiency + battery-side system consumption (W)].

The usable fraction represents the energy window between the starting charge and the retained reserve. System consumption is measured on the battery side in this model. If the supplier already provides measured usable energy at the load under specified conditions, divide that value by the corresponding load power instead of applying the same losses twice.

Example A: a hypothetical portable-power requirement

Assume 1,000 Wh nominal energy, a 90% usable fraction, 90% inverter efficiency, 10 W battery-side system consumption and a constant 200 W load, with no charging during operation. Estimated runtime is 1,000 × 0.90 ÷ (200 ÷ 0.90 + 10) = 3.88 hours.

For four hours under those assumptions, the nominal energy requirement is approximately (200 ÷ 0.90 + 10) × 4 ÷ 0.90 = 1,032 Wh. This is an energy calculation, not a complete product selection. Continuous output and startup capability must also be sufficient, with provision for the actual environment and intended reserve.

All equipment and efficiency figures in this example are assumptions, not HSY product specifications or measured runtime results. Changing the usable fraction to 80% and efficiency to 85%, with the other assumptions unchanged, reduces the 1,000 Wh estimate to about 3.26 hours. Temperature, battery ageing, varying loads, low-load shutdown and protection settings can change the result.

Example B: an energy budget for essential household loads

Assume selected essential loads average 0.5 kW for six hours. They require 3 kWh at the load. With an assumed 90% usable fraction and 90% one-way conversion efficiency, and temporarily excluding system consumption, nominal storage would be approximately 3 ÷ (0.9 × 0.9) = 3.70 kWh. Excluding system consumption makes this estimate optimistic; add the actual system demand and an appropriate planning allowance.

The 0.5 kW average does not determine inverter size. Simultaneous demand or startup demand may be much higher. This is not a whole-home backup design or confirmation that a product can connect directly to household wiring. Home battery sizing also depends on individual needs and installation conditions, as discussed in the Energy Saving Trust battery storage guide.

4. Read a real product specification: CYS01

The CYS01 product page lists 300 W rated output, 296 Wh stored energy and 450 W peak output. The 300 W figure addresses continuous output capability; 296 Wh describes stored energy. The 450 W peak figure is not a continuous operating rating.

Dividing 296 Wh by an appliance’s wattage does not establish verified runtime. Confirm the peak duration, relevant output-port ratings and electrical version for the proposed order. This guide does not assign assumed efficiency to CYS01 or guarantee compatibility with a particular appliance.

5. Match the buying brief to the application

  • Portable power stations: describe the equipment, simultaneous-use pattern, carrying needs and charging opportunities. Plastic, metal and wheeled formats help compare handling requirements, but enclosure material or wheels do not establish electrical capability.
  • Home energy storage: distinguish a battery module from a system that includes an inverter. Specify essential loads, backup duration, existing inverter details and installation location. A battery module should not be assumed to power AC appliances directly.
  • Commercial and industrial energy storage: provide a load profile, maximum simultaneous demand, phase arrangement, backup or peak-shaving objective, charging window and site conditions. Systems with equal kWh can have different kW capabilities and operating constraints.

If charging while supplying loads is important, confirm that the specific product supports this mode and check its input/output limits. Solar-panel nameplate power is not constant available charging power throughout the day. Without a defined charging profile, start with a no-charging runtime estimate.

6. What to include in a quotation enquiry

  • Destination country, application, purchase quantity and preferred product family.
  • Equipment nameplates or data sheets showing voltage, frequency, running power and known startup requirements.
  • Which loads operate together, their daily schedule and the required continuous operating time.
  • Reserve requirements, charging source, ambient temperature and available installation space.
  • Battery-only or complete-system requirements, with responsibility for the inverter, controls, wiring and commissioning identified.
  • OEM/ODM requests and the specification version or documentation to be confirmed, without assuming certification, minimum order quantity, lead time or warranty terms.

If you have not selected a model, use the existing enquiry form’s “Help me select” option and share the equipment information available. Discuss selection and request a quotation from HSY.

Frequently asked questions

Does more capacity mean more output power?

Not necessarily. Energy capacity and continuous output are separate specifications. More kWh does not automatically increase the inverter or port kW limit.

Is a sufficient peak wattage enough to guarantee startup?

No. Duration, starting current, load behaviour and protection settings also matter. Check the specific equipment and, where needed, verify operation under agreed conditions.

Can I use the maximum wattage on an adapter to calculate runtime?

It can provide an initial upper-power reference, but it may not represent average consumption. Charging stage, operating mode and duty cycle affect demand. Where practical, obtain actual power and energy measurements using an appropriate method.

Does this guide replace final product selection?

No. It helps structure requirements and compare specifications. Confirm the model, electrical configuration, scope of supply and performance-verification conditions in writing before purchase.

IP Geolocation by DB-IP